Most Viewed How To Do A Blend Haircut With Clippers You Should Try

Saturday, 28 May 2022

Three-eighths of an inch 4. This way you can blend it in without worrying about cutting too much hair off the two areas.

Pin On Cosmo Info

In the winter we usually leave it a little longer and do a 3 on the back and sides 8 on top and blend with a 4.

How to do a blend haircut with clippers. The guard has to be flat against the head and once the clippers are turn on you should move straight up. What are haircut numbers and hair clipper sizes. Clipper cut the si.

Used around the ears and neck 1. Claim your free membership at httpwwwhowtocuthairtvImprove your barbering skills with over 15 hours of HD streaming video education and over 40 pages o. Slowly move the clippers from one side of the comb to the other to cut any of the hair thats sticking out through the teeth.

Jun 27 2012 - For beginners. Blending The Two Lengths. If you find any poorly blended or uneven spots while you go go back over them with the appropriate clipper guard.

Three-fourths of an inch 7. Work all the way back to the crown making sure to leave the hair longer in the crown. As shown in this video.

How To Do A Fade Haircut With Clippers. From the bottom to the top and back again. Clipper Lengths Stand-Alone Clippers.

One-eighth of an inch 2. To determine how much hair to cut consult with the client and show him the amount to be cut on the front side of the head. If you simply cut with the clippers and stop there the haircut will still look a little home done.

To begin the haircut start on the top. Change to a bigger guard. If youre right-handed cut from right to left.

Repeat this step on each side of the center guide making sure to keep your. Locate the fade lines. Then start with the sides and the back while blending on the top.

An overview to get a fade haircut. Pick up a center section starting in the front and over-direct to the middle of the ear leaving the hair longer in the front. One-fourth of an inch 3.

This will be the blending guard. One-half of an inch 5. Seven-eighths of an inch 8.

To blend the upper portion which has more hair to the lower part you might need to change the attachment comb to a larger one. Do this all the way around the head. You should also turn the blade around and use it to go around the edges of the hairline.

To blend the midsection of the hair where the two lengths meet choose a guard size in between the top length and bottom length. Hold the clippers in your other hand with the guard removed and switch them on. Making the Cut.

Determine the length of your fade haircut. Comb the hair back down onto the scalp to check that it is even. Comb your hair going with the grade of your hair.

If youre left-handed make your cut from left to right. Run the clipper blade along the side of the comb nearest you from right to left to evenly trim the ends of the hair. On the top of your head it should be straight forward on the sides and back it should be straight down.

To blend use an upward rocking motion ie. Things You Need Before Doing A Fade Haircut. I blend the two lengths with a 3 all the way around the head.

A blended hairstyle is accomplished by using various clipper guards to create a seamless fade. When you first start with a regular taper place the longest guard on your hair clippers or set it to the highest length setting depending on your hair clippers. Move the clippers in the opposite direction of your hair growth.

Once the guard is chosen start off at the bottom of the hairline and move upwards until hair begins to trim off. This should be where the two lengths meet. For the back of the head put a grade-two blade on your clippers for a standard cut or longer or shorter as desired.

Hold the clippers in your dominant hand and press it against the side of your comb. Move your clippers on the shortest guard setting along the nape and edges of the sides. It is better to go to low than too high because when we blend we will just take out the access length.

When youre blending with clippers you need to place the clippers flat against the head with the guard in place casing upwards. Its a rough feeling if you are going against the grade. Clean the edges with your clippers.

The easy way to notice this is if you rub your hair. Take the clippers and shave up to about 34 of the head or just before the head begins to curve The line in the photo. Five-eighths of an inch 6.

Pin On Men S Hair Cut